Land Rover Series 2.8 liter Performance Engine build

Post pics of your car in here
Post Reply
Spider 1969
Posts: 156
Joined: September 22nd, 2013, 7:21 pm
Contact:

Land Rover Series 2.8 liter Performance Engine build

Post by Spider 1969 » July 15th, 2022, 8:52 pm

Not a race engine but definitely something else than overhauling the standard 2.25 that is presently powering my 1960 Land Rover Series 2.

In need for more torque to cope with modern day traffic conditions I originally intended to upgrade the 2.25 when I stumbled upon a 2.5 liter engine block for sale. The 2.5 liter is basically the 2.25 with a longer stroke as developed for the LR 90/110/Defender. I also found out that the UK based ACR has developed a CNC ported head, larger bore pistons to increase the capacity of this engine to 2.8 liter as well as a camshaft and carb kit. Aim of this kit is to increase torque and drivability which makes it perfect for my intentions.

Most parts can be interchanged between the 2.25 and the 2.5 but since I am using my Landy frequently I needed to find also a head, timing cover, sump etc. to be able to swap the complete engine after build. The head I found online as well as a donor diesel engine for the other bits and bobs. Flywheel and housing are different from other series and difficult to acquire but in the end I succeeded. In hindsight I would have been better (less expensive) off if I had started with a complete 2.5 engine as a basis.

Inspection of the 2.5 block revealed that the crank needed grinding and it turned out that the cost of a new crank is close to machining so I opted for a new crank. Send of the head to ACR for porting and skimming and it returned with the over size pistons, H-beam rods, camshaft and the SU HS6 Carburetor kit.

Block was bored and skimmed locally during which I checked the dimensions of the new crank and cleaned, sand blasted and painted all ancillary parts.

After return of the bored block it was painted too so the build could commence. Ring gaps and bearing clearances were checked and all within spec. When inserting # 1 piston the upper rail of the oil control ring snatched between the piston and cylinder wall. Possibly due to the type of ring compressor in combination with the large bore (95 mm). rail was destroyed and luckily only minor damage to the piston. Slight set back in time however due to waiting for the new rail.

While waiting I finished inserting the other pistons with another design ring compressor and inserted #1 piston without rings so I could start installing and timing the camshaft. More to follow.

Regards,
Charles
Attachments
0_LANDY_S2-001.JPG
YE OLD LANDY
0_LANDY_S2-001.JPG (686.08 KiB) Viewed 405 times
1_New Block-001.jpg
Start of the project
1_New Block-001.jpg (960.45 KiB) Viewed 405 times
1_New Block-002.jpg
Inspection time
1_New Block-002.jpg (846.3 KiB) Viewed 405 times
2_New Parts-001.jpg
Shiny Things alert!
2_New Parts-001.jpg (947.75 KiB) Viewed 405 times
3_New Crank-001.jpg
Another shiny thing
3_New Crank-001.jpg (842.12 KiB) Viewed 405 times
3_New Crank-002.jpg
Quality check
3_New Crank-002.jpg (688.52 KiB) Viewed 405 times
4_Block_Machined-001.jpg
Back from the machine shop, decked, bored and cam bearings fitted
4_Block_Machined-001.jpg (807.09 KiB) Viewed 405 times
4_Block_Painted-001.jpg
Paint!
4_Block_Painted-001.jpg (1.1 MiB) Viewed 405 times
5_Rotary Assembly-001.jpg
Bearing clearance within spec
5_Rotary Assembly-001.jpg (629.85 KiB) Viewed 405 times
5_Rotary Assembly-002.jpg
Crank T-Seals fitted
5_Rotary Assembly-002.jpg (863.78 KiB) Viewed 405 times
5_Rotary Assembly-003.jpg
Crank end float within spec
5_Rotary Assembly-003.jpg (745.91 KiB) Viewed 405 times
8_Pistons-001.jpg
Fitting the rings
8_Pistons-001.jpg (748.7 KiB) Viewed 405 times
8_Pistons-002.jpg
Oil rail escaped
8_Pistons-002.jpg (661.08 KiB) Viewed 405 times
8_Pistons-004.jpg
Rail destroyed
8_Pistons-004.jpg (632.8 KiB) Viewed 405 times
8_Pistons-005.jpg
New ring compressor
8_Pistons-005.jpg (714.63 KiB) Viewed 405 times
6_Cam-002.jpg
Cam fitted, followers to go in
6_Cam-002.jpg (968.67 KiB) Viewed 405 times
6_Cam-003.jpg
Cam end float within spec
6_Cam-003.jpg (873.9 KiB) Viewed 405 times
7_Timing-001.jpg
Cam timed
7_Timing-001.jpg (866.99 KiB) Viewed 405 times
7_Timing-002.jpg
All new parts fitted
7_Timing-002.jpg (883.01 KiB) Viewed 405 times

Post Reply

Who is online

Users browsing this forum: No registered users and 8 guests