Strength of 2.0 16v crank?

Competition engines and ancillaries - general discussion
Post Reply
Mats
Posts: 40
Joined: October 24th, 2006, 9:21 am
Location: Gothenburg, Sweden
Contact:

Strength of 2.0 16v crank?

Post by Mats »

Is the strenght of the crank in the Delta integrale 16v engine a known weak spot or is it possible to regrind the big end bearing surfaces undersized? I'm talking a couple of millimeters here and maybe offset grind it to reduce the stroke.
Will it upset the balance of the reciprocating assembly or is it no different from shifting to a lighter set of pistons and rods?
/Mats Strandberg
Guy Croft
Site Admin
Posts: 5039
Joined: June 18th, 2006, 9:31 am
Location: Bedford, UK
Contact:

Post by Guy Croft »

Quote from email to me today by member and noted drag race specialist Greg Demetriadis from Piraeus Greece (16v Integrale):

"... I never had a problem with OEM crankshaft with good balancing. I also make them knife edged (...to lighten and improve aerodynamics). No problem at all at 700 bhp at the wheels.."

As for the other mods, you should consult a crank balancing expert before any lightening mods and you MUST NOT grind that heat treated crank or you'll have no surface harness at all. (I know this from experience and it is also stated in the factory manual).

GC
Mats
Posts: 40
Joined: October 24th, 2006, 9:21 am
Location: Gothenburg, Sweden
Contact:

Post by Mats »

So if I understand you correctly, grinding the journals is a big no-no? What about hardening it afterwards? Nitriding it again? Straighten it and re-balance it afterwards perhaps?

As you maybe guessed by now I really don't know the manufacturing process of a crank. I don't underestimate the importance of correct surface treatments and balance though.
/Mats Strandberg
Guy Croft
Site Admin
Posts: 5039
Joined: June 18th, 2006, 9:31 am
Location: Bedford, UK
Contact:

Post by Guy Croft »

Just trust me Mats for now, don't grind it.

I tried a search but I do not appear to explained 'why not?'

You will understand that it is not possible to give detailed explanations for everything, especially 'why can I not do this..'.

I do my best to keep up but it's not easy. Sometimes you just have to take my word and move on.

GC
Mats
Posts: 40
Joined: October 24th, 2006, 9:21 am
Location: Gothenburg, Sweden
Contact:

Post by Mats »

Ok, I'll leave it alone.
Thanks for clearing that out.
/Mats Strandberg
Testament
Posts: 101
Joined: June 22nd, 2006, 7:47 pm
Location: Taupo, New Zealand
Contact:

Post by Testament »

What about the 80mm and 71.5mm Fiat TC cranks? are they heat treated also? or is it ok to grind them?
Guy Croft
Site Admin
Posts: 5039
Joined: June 18th, 2006, 9:31 am
Location: Bedford, UK
Contact:

Post by Guy Croft »

I think it's OK, yes, I often have, but that said, with the 1585cc crank I have tended to heat treat it on competition engines if it needed a grind, being cast rather than forged like the 1756cc one. I think both are probably induction hardened, though I have not proof of this, never had them analysed, not done that many of those two engines.

GC
ACE-GREG
Posts: 8
Joined: June 24th, 2006, 8:30 am
Location: Piraeus GREECE
Contact:

Post by ACE-GREG »

Mats,

Always, trust Guy.
Especially at engine internals...

Greg
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests