Drysumping

Competition engines and ancillaries - general discussion
Post Reply
torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Drysumping

Post by torkil » Tue Oct 10, 2017 7:47 am

Hi Have a Titan Type 2 Drysumppump with 30 teeths pulley , Power take off on camchaft on gearbox end , conected with belt ,to get it lower located on the engine, I read that the pump hawe to rotate half speed off the crank and also havve to rotate clockwise , so i have to use a 30 teeth on the camchaft too, Any hints or sites i can i can read more ,? Ove Thorkildsen Oslo
GC_41

Guy Croft
Site Admin
Posts: 5004
Joined: Sun Jun 18, 2006 9:31 am
Location: Lincoln, UK
Contact:

Re: Drysumping

Post by Guy Croft » Tue Oct 10, 2017 11:18 am

half crank speed is normal for the Titan pump Ove.

Camshaft is half crank speed... OK.

However, if you run the pump off the cam at the gearbox end it may be too high in the engine bay to work properly. The hose to the pressure stage from the tank should be gravity-fed not sucking thru a height (where the pump is higher than the tank). The scavenge system also may not work if the scav stages have to suck the oil 2 ft above the sump..

G
Guy Croft, owner

torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Drysumping

Post by torkil » Tue Oct 10, 2017 5:13 pm

Yes is will bee fitted low down , with a long belt , Not directly on camchaft, Ove
GC_41

Guy Croft
Site Admin
Posts: 5004
Joined: Sun Jun 18, 2006 9:31 am
Location: Lincoln, UK
Contact:

Re: Drysumping

Post by Guy Croft » Tue Oct 10, 2017 10:23 pm

post photos so I can check your layout..

GC
Guy Croft, owner

torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Drysumping

Post by torkil » Sat Oct 14, 2017 8:20 pm

Yes i will send picks , wery difficult , no one to discuss with here ,Possible i buy a titan pulley 30 teeth and make a take off from cam on the gearbox side , Titan caal ther pitch on pulley for 3/8 inch , Do you know what that says ? , and i also wonder if Gilmer belts fits , They make werey long belts.
GC_41

Guy Croft
Site Admin
Posts: 5004
Joined: Sun Jun 18, 2006 9:31 am
Location: Lincoln, UK
Contact:

Re: Drysumping

Post by Guy Croft » Sun Oct 15, 2017 12:24 pm

The Titan 30T pulley is 3/8" pitch trapezoidal (rectangular teeth).

It will accept industrial or automotive pitch - auto 3/8" pitch is stronger but if you use a 3/4" wide drive belt either will do. There are more lengths of belt available in industrial than automotive.

If you run off the cam you need to work out a position for the pump so that you can be sure to find a belt of the right length. It is a good idea to use a tensioner. The drive pulley from the cam should have flanges front and rear so the belt stays in place.

In the photo the drive pulley has only one flange (there is not enough room for two flanges) but there is a flange on the rear of the tensioner pulley.

It is easier to use a tensioner than to try and mount the pump in the 'perfect' position to get the belt tight.

I can help with belts & pulleys etc if you need me..

G
Attachments
IMG_7682.JPG
IMG_7682.JPG (118.19 KiB) Viewed 271 times
Guy Croft, owner

torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Drysumping

Post by torkil » Sun Oct 15, 2017 2:12 pm

Thanks Mr , Croft ,Wery useful info about Drysumping, Defenly need belt and pullyies.
GC_41

torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Drysumping

Post by torkil » Sun Oct 15, 2017 2:17 pm

Hi , do you use 2x 25 toots pullys , Difficult to count?
GC_41

Guy Croft
Site Admin
Posts: 5004
Joined: Sun Jun 18, 2006 9:31 am
Location: Lincoln, UK
Contact:

Re: Drysumping

Post by Guy Croft » Sun Oct 15, 2017 5:39 pm

Ove I can get any pulley made you want but for cam drive you need 1:1 drive

good for 9500rpm engine speed...

30 cam - 30 pump

GC
Guy Croft, owner

torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Drysumping

Post by torkil » Tue Oct 17, 2017 10:23 am

Thanks whats the price for a 30 teeth doble flanget pulley that i can make some pices and fit on the cam?
GC_41

Guy Croft
Site Admin
Posts: 5004
Joined: Sun Jun 18, 2006 9:31 am
Location: Lincoln, UK
Contact:

Re: Drysumping

Post by Guy Croft » Tue Oct 17, 2017 11:14 am

sorry my mistake - the standard series 2 Titan pump has 22 teeth not 30

I have two types of drive pulley - see photo - with 22T

Both are designed to run at 1/2 crank speed - One has two flanges, the other has one flange with a tensioner with rear flange. The pulley cost (of either type) is £90 + mailing.

It would be much more to make one single pulley (& design time) so if you use one of these it would be better..

G
Attachments
IMG_9979.JPG
IMG_9979.JPG (108.49 KiB) Viewed 226 times
IMG_9980.JPG
IMG_9980.JPG (114.74 KiB) Viewed 226 times
Guy Croft, owner

torkil
Posts: 63
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Drysumping

Post by torkil » Tue Oct 17, 2017 5:19 pm

Thanks for useful info, Mr .Croft
GC_41

Guy Croft
Site Admin
Posts: 5004
Joined: Sun Jun 18, 2006 9:31 am
Location: Lincoln, UK
Contact:

Re: Drysumping

Post by Guy Croft » Tue Oct 17, 2017 5:32 pm

my post amended dear Ove,

I apologise for all the mistakes I am making,

GC
Guy Croft, owner

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests