BMW 2003 Mini Cooper S

Post pics of your car in here
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

So before doing any extra work we decided to run the car a little to see if it was still running and whether or not the bubbling over issue had sorted itself out. After doing all the hydrocarbon tests etc it appears coolant was not escaping into the coolant.
Therefore i gave the car a good bleed and decided to run. I ran it into town and got stuck in some traffic and then noticed pockets of steam coming from the front and the fans were on, but the temp warning light was not on. Parked the car eventually in a space and got out, only to notice a waterfall from the radiator. Uh oh! Something has gone seriously wrong here, and no coolant left.
Managed to fill her up with water and get her home, funnily enough i did not lose much more coolant. Seems to be fine if the car is moving forward but can't handle not moving e.g. traffic.

Anyway new Radiator has also been purchased, so a new Mishimoto Aluminimum radiator is on its way with lifetime warranty. Also we should expect to have all parts in my hands by end of the week so i will be busy this weekend hopefully taking it all apart. I can't believe it has just cost me and absolute bomb, but hopefully it is worth it. Still haven't taken the head off so we will wait and see what we find. I really hope it is just a dodgy gasket and we have got away from any other damage.
Local machine shop are also willing to skim head so this will be done also alongside a full proper service.

Can't wait to get this done as i need this fixed so i can move on to get the engine out of the Alfa and change the clutch and diff over with new exhaust manifolds. Baby due date only few weeks away now so got alot to do.
GC_21
Guy Croft
Site Admin
Posts: 5039
Joined: June 18th, 2006, 9:31 am
Location: Bedford, UK
Contact:

Re: BMW 2003 Mini Cooper S

Post by Guy Croft »

I suspect you may have corrosion betw liners and block Will.

When you have checked everything else and the engine is still losing coolant and you cannot see why this is the cause. I had this on my Range Rover, old engine was scrap. A top-hat liner V8 engine from Turner Engineering is now installed.

When the heads were off I could not see any leakage path - but it showed up on hot pressure test of the crankcase.

G
Guy Croft, owner
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Hi Guy, i am really hoping it is not the case but i have as much crossed as possible. I not going to know really until the car is back together again.

Yesterday alot more parts arrived in the post, so now we have everything so i can get started stripping her down and then trying to find the cause of low compression and check to see where all the leaks are coming from.
So new Aluminimum radiator, head gasket, intake gasket, exhaust gasket, thermostat, head bolts (upgraded ARP items), supercharger oil replacement kit, new auxillary shortened belt to suit, 15% reduced supercharger pulley, cooler NGK spark plugs, oil filter and oil ready to go.
Still need a few other parts e.g. the camshaft stretch bolt etc
But i can at least now start to strip the car down, the cylinder head will then go to a local machinist where the head will be skimmed.
I will take plenty of photos and make up a sort of strip down and rebuild procedure, it maybe of interest to someone.
See pictures of car before starting and parts
Attachments
Car in one piece before starting
Car in one piece before starting
DSC_2263.jpg (185.79 KiB) Viewed 26046 times
Mishimoto Aluminium Lifetime gaurantee radiator
Mishimoto Aluminium Lifetime gaurantee radiator
DSC_2275.jpg (86.81 KiB) Viewed 26046 times
Lots of nice new parts
Lots of nice new parts
DSC_2278.jpg (121.04 KiB) Viewed 26046 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Been very busy today stripping down the Mini. It is a big job, but i did eventually get the head off.
Got a few more parts to buy due to condition of parts coming off. Everything is going to get a good clean up aswell.
I will post pictures up during the week, but the compactness of the Mini makes everything very difficult to get into a rhythm. Some of the bolts are very difficult to get a good grip on so they take a little bit of thinking.
Taken plenty of pictures of wiring routing aswell as that is going to be tricky to get everything back where it should be.
Tomorrow job is to strip the cylinder head ready for machining etc
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Here's some step by step pictures
Jack up car, remove wheels
Remove front bumper, take care and unplug wires as you go along
Remove front aluminium crash bar, pull wiring clear of crash bar
Attachments
Bonnet open ready to go
Bonnet open ready to go
DSC_2280.jpg (35.13 KiB) Viewed 26036 times
Jack up front of car and remove front wheels for ease of access
Jack up front of car and remove front wheels for ease of access
DSC_2281.jpg (47.33 KiB) Viewed 26036 times
Remove inner wheel arch front screws
Remove inner wheel arch front screws
DSC_2282.jpg (26.81 KiB) Viewed 26036 times
Push inner wheel arch out the way and remove bumper screw in corner
Push inner wheel arch out the way and remove bumper screw in corner
DSC_2283.jpg (41.99 KiB) Viewed 26036 times
Remove bolts and screws underneath car
Remove bolts and screws underneath car
DSC_2284.jpg (30 KiB) Viewed 26036 times
Remove torx screws holding front bumper in place
Remove torx screws holding front bumper in place
DSC_2285.jpg (34.69 KiB) Viewed 26036 times
Bumper gone
Bumper gone
DSC_2286.jpg (55.37 KiB) Viewed 26036 times
Undo bolts holding on front crash bar
Undo bolts holding on front crash bar
DSC_2287.jpg (43.1 KiB) Viewed 26036 times
Remove crash bar
Remove crash bar
DSC_2289.jpg (59.95 KiB) Viewed 26036 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Once bumper and crash bar removed, now remove radiator assembly. Pretty tricky!
Remove front frame rail attachments
Pull wiring clear of plastic assembly, take note of where wires route
You can seperate a/c rad clear and you don't need to unplug
Strip down radiator assembly to remove radiator ready for repalcement
Attachments
Crash bar removed
Crash bar removed
DSC_2290.jpg (51.91 KiB) Viewed 26192 times
Front frame rail
Front frame rail
DSC_2291.jpg (45.26 KiB) Viewed 26192 times
Front frame rail bolts, knock forward once bolts removed
Front frame rail bolts, knock forward once bolts removed
DSC_2292.jpg (33.24 KiB) Viewed 26192 times
Pull radiator assembly clear and disconnect radiator bolts holidng to a/c radiator.
Pull radiator assembly clear and disconnect radiator bolts holidng to a/c radiator.
DSC_2295.jpg (53.98 KiB) Viewed 26192 times
Front radiator assembly
Front radiator assembly
DSC_2296.jpg (51.39 KiB) Viewed 26192 times
Push plastic locating pins through to release top of radiator
Push plastic locating pins through to release top of radiator
DSC_2297.jpg (51.16 KiB) Viewed 26192 times
Remove radiator from assembly
Remove radiator from assembly
DSC_2298.jpg (53.42 KiB) Viewed 26192 times
Radiator and fan assembly
Radiator and fan assembly
DSC_2299.jpg (60.37 KiB) Viewed 26192 times
Old vs new radiator. New one is thicker aswell
Old vs new radiator. New one is thicker aswell
DSC_2300.jpg (56.21 KiB) Viewed 26192 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Now start taking other parts off top of engine
First start with Intercooler
Remove airbox and pipe-work etc along with ECU and housing. Unclip and lift up ECU, then unplug wires and pull out, store carefully!
Remove spark plug coil, be careful
Lots of wires and plugs to remove and pipes, take note where everything goes and where it routes
Remove injector rail, unclip from top of injectors, carefully! You have to unclip fuel line so be carefull, it may still be under pressure and fuel will come out.
Remove drivers side engine steady, support engine with axle stand and jack

Now it really starts to get tricky with hard to reach bolts and nuts etc!
Attachments
Unbolt 4 bolts holding IC plastic shroud
Unbolt 4 bolts holding IC plastic shroud
DSC_2301.jpg (42.45 KiB) Viewed 26192 times
Undo clamps either side of IC, wiggle IC free. Do not damage boots if re-using, Inspect carefully if can be re-used
Undo clamps either side of IC, wiggle IC free. Do not damage boots if re-using, Inspect carefully if can be re-used
DSC_2302.jpg (46.8 KiB) Viewed 26192 times
IC removed
IC removed
DSC_2303.jpg (43.59 KiB) Viewed 26192 times
Unbolt and remove air filter and box
Unbolt and remove air filter and box
DSC_2306.jpg (35.48 KiB) Viewed 26192 times
Airbox gone
Airbox gone
DSC_2307.jpg (46.88 KiB) Viewed 26192 times
Coil pack remove
Coil pack remove
DSC_2310.jpg (46.7 KiB) Viewed 26192 times
Injector rail, un bolt
Injector rail, un bolt
DSC_2316.jpg (44.54 KiB) Viewed 26192 times
fuel rail gone
fuel rail gone
DSC_2317.jpg (38.81 KiB) Viewed 26192 times
engine steady and mount
engine steady and mount
DSC_2321.jpg (41.9 KiB) Viewed 26192 times
Engine mount removed
Engine mount removed
DSC_2322.jpg (49.09 KiB) Viewed 26192 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Need to remove intake manifold
Lots of pipewrork and bolts and wiring to remove and keep clear!
You have to undo the throttle body housing mounts and connections and have to pop off a few hoses. You need the engine mount clear so you can get
Intake manifold once removed, plu port to prevent poor getting in there.
Now remove thermostat located to right of head below cylinder head
Remove rocker cover, take care as these bolts seem to be soft and corrode easily!

Now start to take even more time, turn engine so arrow on cam sprocket is at 12 o'clock remembering that engine is slanted backwards so it will not point straight up!
Mark arrow with sprocket and chain, mark crank anti vibration pulley.
Remove tensioner for chain.
Hold crank sprocket whilst undo the cam bolt. do not remove yet.
Remove cam sensor as we are replacing anyway

Undo the exhaust manifold, be carefull as access is limited and do not round off the bolts, they are small and ease to slip off!
Remove heat shield first and push back to get access to bolts
Attachments
Un bolting the throttle body
Un bolting the throttle body
DSC_2327.jpg (39.07 KiB) Viewed 26192 times
Intake gone
Intake gone
DSC_2329.jpg (44.2 KiB) Viewed 26192 times
Remove thermostat x3 bolts
Remove thermostat x3 bolts
DSC_2334.jpg (51.78 KiB) Viewed 26192 times
Thermostat
Thermostat
DSC_2336.jpg (54.43 KiB) Viewed 26192 times
Rocker cover gone
Rocker cover gone
DSC_2340.jpg (46.11 KiB) Viewed 26192 times
Mark cam sprocket
Mark cam sprocket
DSC_2341.jpg (54.58 KiB) Viewed 26192 times
Remove tensioner from back of engine, access via wheel arch inner wing
Remove tensioner from back of engine, access via wheel arch inner wing
DSC_2343.jpg (41.12 KiB) Viewed 26192 times
Cam sensor removal
Cam sensor removal
DSC_2344.jpg (32.96 KiB) Viewed 26192 times
Sensor removed
Sensor removed
DSC_2345.jpg (29.68 KiB) Viewed 26192 times
Remove access bolts from end up head to un bolt chain guide location bolts
Remove access bolts from end up head to un bolt chain guide location bolts
DSC_2346.jpg (42.76 KiB) Viewed 26192 times
Un bolt exhaust manifold
Un bolt exhaust manifold
DSC_2348.jpg (39.45 KiB) Viewed 26192 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Now unbolt cam sprocket, tie chain up out the way, do not drop inside engine!
Once removed then pull chain guides up out the way.
Now unbolt cylinder head bolts in sequence as per manual. Start with two bolts located inside timing chain housing.
Then do main head bolts, remember go opposite starting from outside to inside bolts, little turn at a time until torque is released to prevent warping.
Pull up out the way, these bolts will be discarded! So buy new ones. We have gone for ARP upgraded stud and nuts which are re-useable.
Pull off head carefully.
Before leaving vehicle, plug all holes to prevent stuff getting in engine.
Note position of valves etc for rebuild later
Attachments
Head removed, check condition of bores
Head removed, check condition of bores
DSC_2350.jpg (40.87 KiB) Viewed 26192 times
Front end doesn't look very good now!
Front end doesn't look very good now!
DSC_2351.jpg (46.21 KiB) Viewed 26192 times
Inspect head to start with before cleaning, remove spark plugs etc
Inspect head to start with before cleaning, remove spark plugs etc
DSC_2355.jpg (43.03 KiB) Viewed 26192 times
Exhaust valve on cylinder 1 look very white compared to others. Same cylinder as low compression.
Exhaust valve on cylinder 1 look very white compared to others. Same cylinder as low compression.
DSC_2357.jpg (38.65 KiB) Viewed 26192 times
Valve positions
Valve positions
DSC_2362.jpg (43.59 KiB) Viewed 26192 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

Now the fun begins
Stripping down the head for skimming and pressure testing. We found the cylinder head gasket to be in good condition and no signs of anywhere where we could lose compression. Just a suspect valve.
I think possibly dodgy valve seat burnt or similar so we will see.

I stripped the head on a bench.
Take care not to put cylinder head flat on mating face as you will bend or damage a valve.
Undo camshaft and rocker cover bolts. do this little by little to prevent damage. Same method as removing cylinder head bolts
Lay parts out logically so you know exactly where they came from e.g. cardboard with rough sketch of where they came from.
Lift off rockers first as one piece with shaft
Then remove camshaft
Inspect all parts for wear or damage
Use valve remover, so you have to compress springs and pop off the collets and then release pressure to remove springs and retainers etc.
Check valve for wear in valve guides
Inspect seats, all exhaust seats look like the need a good grinding
Inspect head for cracks around spark plugs holes etc etc
I made two seperate cardboard organisers to keep valves and srpings together correctly. I will measure length of springs etc. In the past when i had access i also inspected valve springs on a dyno, but i don't have access anymore.
Next job is to send head off for work
Attachments
Cylinder head on bench clamped down to remove rockers etc
Cylinder head on bench clamped down to remove rockers etc
DSC_2363.jpg (47.23 KiB) Viewed 26192 times
Cardboard head organiser
Cardboard head organiser
DSC_2364.jpg (30.09 KiB) Viewed 26192 times
Rockers removed
Rockers removed
DSC_2365.jpg (43.82 KiB) Viewed 26192 times
Remove cam
Remove cam
DSC_2367.jpg (47.83 KiB) Viewed 26192 times
Valves etc removed
Valves etc removed
DSC_2368.jpg (48.92 KiB) Viewed 26192 times
Cardboard organiser
Cardboard organiser
DSC_2370.jpg (33.57 KiB) Viewed 26192 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

So cylinder head is off to Stanwood Engineering today to get pressure tested & sorted etc ready for top end rebuild.
Thanks to Guy for the recommendation.
After speaking with Stanwood over the phone i am more than happy to send the cylinder head down to them to do the required work. Fingers crossed that the pressure test does not highlight any issues.
I will add pictures once i have a cylinder head back and start rebuilding it
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

So we got the confirmation last week that the cylinder head pressure tested ok. However the valve guides etc showed to be worn and needed to be replaced. Amazingly, these valve guides are only available from a US source and with shipping etc and cost of the guides etc they were going to cost too much. Then after factoring in the other machining work which is required w.g. head skim and recutting the valves into new raised valve seats the cost was prohibitive. I have actually sourced a completely re-conditioned cylinder head from Minitech spares which is a cheaper option than reconditioning my own cylinder head.
Stanwood Engineering have been very helpful and very professional in their service and i will use again. Just this time due to poor parts availbility it was not a viable option.

After receiving the new cylinder head it looks very good and clean ready to fit. I am going to carry out a few checks before i do fit the head just for my own peace of mind also, but i feel this was a much better option. I could in fact chosen to upgrade to a John Cooper Works cylinder head for the same price it was going to cost to recondiition my own cylinder head, but since the modifications made to the John Cooper Works head are very minimal (only exhaust ports have revised design) i decided that it was not worth the extra expense. Its a daily use road car anyway and we just want something that works well and reliably.

It is believed that the engines used in the BMW Cooper S are Chrysler engines. I haven't been able to 100% confirm this, but it does seem to be well talked about online. I have to admit i do believe this as more and more manufacturers buy parts(e.g. engines) from other manufacturers.

I think we will just put the old head back together again to keep in one pieace and either keep as a spare and use in the future as a project head, or i may indeed sell the head to try and re-coop some of the extreme cost involved in fixing the car.
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

So last night i decided to get to work to get this car fixed and back on the road for the end of the month.

Before re-fitting the head i decided to give the supercharger oil a service, so using a syringe i pulled the old oil out(of which very little remained) and refilled with correct Eaton charger oil.
140ml in front of charger and 40ml in back (water pump side).

Also i started work cleaning up the block mating surface for the cylinder head, this will be finished off tonight and hopefully i can start fitting the head back on.
Still need to clean up the threads in the block ready for fitting the ARP head studs, then we can start getting everything fitting back down.
Attachments
Front of charger 3/16" allen key bolt, i had to use metric allen key because the bolt was soft and started enlarging!
Front of charger 3/16" allen key bolt, i had to use metric allen key because the bolt was soft and started enlarging!
DSC_2516.jpg (143.03 KiB) Viewed 25204 times
WP side of charger, another 3/16" allen key bolt
WP side of charger, another 3/16" allen key bolt
DSC_2517.jpg (105.34 KiB) Viewed 25204 times
Recon cylinder head ready for fitting on sensors
Recon cylinder head ready for fitting on sensors
DSC_2514.jpg (159.03 KiB) Viewed 25204 times
Nicely clean ready to fit, just need to time cam to allow correct timing for assembly
Nicely clean ready to fit, just need to time cam to allow correct timing for assembly
DSC_2515.jpg (144.81 KiB) Viewed 25204 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

I am having to do little by little at the moment after work in the evening. Last night i gave the black and cylinder head a final clean before starting to refit.
Once cleaned up, i then installed the ARP head studs, making sure that the threads were clean and free of oil or water(more difficult than you think!)
These were then installed hand tight with a small allen key.
Once these were locked in the headgasket was then fitted (brand new!), then the head was carefully installed making sure it did not bind on anything. It was quite difficult to line up because the exhaust manifold kept getting in the way and i had to try and feed the timing chain up through the head at the same time, but i did eventually manage it on my own(somehow).
Next job was then to line up head and make sure it was sitting flush on the dowels and gasket.
Then was on to placing in the washers and before fitting the nuts make sure to use assembly lubricant. This is quite important to make sure you get accurate torque readings for the fasteners and helps prevent any binding during assembly.

Unfortunately i ran out of time after this, so it will continue hopefully tonight and over the weekend.

Job tonight is to refit Inlet manifold and accessories etc and get exhaust manifold connected and then move on to servicing the auxillary belt drive with new belt, smaller reduced supercharger pulley. Replace tensioner damper bushes with PU versions and fit a safety stop on the damper to prvent damage if the belt breaks.
I want to make sure the car is a little more fun but still remain practical and reliable. Time wil tell.
Attachments
Head being cleaned up ready for gasket fitment
Head being cleaned up ready for gasket fitment
DSC_2518.jpg (156.69 KiB) Viewed 25202 times
Headgasket on
Headgasket on
DSC_2520.jpg (153.35 KiB) Viewed 25202 times
Head being installed
Head being installed
DSC_2521.jpg (152.98 KiB) Viewed 25202 times
ARP assembly instructions and part no.
ARP assembly instructions and part no.
DSC_2522.jpg (172.32 KiB) Viewed 25202 times
GC_21
Will01
Posts: 590
Joined: November 26th, 2012, 3:50 pm
Location: Dumfries, Scotland
Contact:

Re: BMW 2003 Mini Cooper S

Post by Will01 »

So managed to carry a bit more work on the Mini over the weekend in between juggling nappy changes and family visits etc.

So the new cylinder head went back on the top of the engine and re-time the cams & crank.
This was relatively simple since you just have to line up the markings. Once the head was installed i also replaced the thermostat housing and thermostat as they are very difficult to get to and repalce, so i thought it was worth changing even though there wasn't an issue with it. The car has done over 100k miles so it makes sense.
I also purchased new rocker cover bolts which cost an absolute fortune from BMW as they have rubber seals which prevent oil leaks. Also the old botls that came off were in appaling condition and had rusted badly(reduced in socket size!)

Once the head and rocker cover was installed i then took the time to service the auxillary belt drive. After removal of the belt with the correct tool(which is highly recommended, as it makes it much easier etc) i checked the condition of the idler bearings etc. In the end we just replaced the belt and fitted new PU bushes to the aux belt damper.
I also fitted a tensioner stop on the damper as this prevents failure to other components if the belt breaks. This is more of damage prevention.

Obviously i also took the time to fit the new smaller SC pulley. We may aswell try to improve the driveability and fun factor also. We only went with a 15% reduction pulley as i have no real wants to upgrade the intercooler or SC at the moment. If you rev the SC faster it will produce more heat, from many others experience the standard cars can cope with 15-17% ok.
At a later date i intend changing the crank pulley for a larger item so this would be a good combo with the current pulley and then we will look at upgrading the Intercooler. These tend to need changing at higher mileages anyway so i also go with 'if you are replacing something, why not upgrade'.

A new timing chain tensioner was purchased as you should never re use the old one, this was fitted and once ready the car was cranked and turned off 3-4 times to allow the tensioner to click into place and tension the chain.
At this stage the engine was not ready to run constantly because of no coolant system, but the engine was run very briefly to get the oil pressure up and make sure no fault codes showed up, which involved a little revving.
All fault codes have now dissappeared and the engine starts much easier and sounds completely different. The throttle response on idle is also much better and caught me un-aware as it revved very quickly and made a lovely supercharger screaming noise.
It is important to note cooler NGK plugs were fitted as well due to higher temperatures being created by the SC now.
Once the car is back together and run up to temperature etc the oil and filter will also be changed. This is always good practice after carrying out major surgery, just in case some poor has got in somewhere.

Next upgrades really will just be to help keep an eye on things e.g. Oil pressure & Water temperature gauges being fitted. There is no such gauges in the car whatsoever which i am not a fan of.
Attachments
Timing chain re-installed
Timing chain re-installed
DSC_2524.jpg (114.34 KiB) Viewed 25197 times
New thermostat and housing
New thermostat and housing
DSC_2526.jpg (142.41 KiB) Viewed 25197 times
New head fitted with rocker cover
New head fitted with rocker cover
DSC_2528.jpg (147.48 KiB) Viewed 25197 times
PU bushes fitted to aux belt damper
PU bushes fitted to aux belt damper
DSC_2529.jpg (200.03 KiB) Viewed 25197 times
SC Pulley comparison
SC Pulley comparison
DSC_2531.jpg (180.83 KiB) Viewed 25197 times
SC Pulley comparison
SC Pulley comparison
DSC_2532.jpg (197.25 KiB) Viewed 25197 times
New pulley installed, old pulley had to be removed with custom puller as stock pulley is press fit. New SC pulley is taper lock style
New pulley installed, old pulley had to be removed with custom puller as stock pulley is press fit. New SC pulley is taper lock style
DSC_2533.jpg (120.69 KiB) Viewed 25197 times
Alta tensioner stop installed. This prevents the tensioner assembly over extending which can cause sever damage to engine components if belt breaks
Alta tensioner stop installed. This prevents the tensioner assembly over extending which can cause sever damage to engine components if belt breaks
DSC_2534.jpg (113.29 KiB) Viewed 25197 times
GC_21
Post Reply

Who is online

Users browsing this forum: No registered users and 3 guests