Need Camchafts for my 2,0 16v engine.used in my X1/9

Road-race engines and ancillaries - general discussion
Post Reply
torkil
Posts: 72
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Need Camchafts for my 2,0 16v engine.used in my X1/9

Post by torkil » Sat Mar 02, 2013 2:58 pm

Hi looking for camchafts for my Fiat X1/9 Abarth Replica . The set up is DTA e48 ECU about 11-1 in compression 40mm throttlebodies ,( will fit 45 soon)4 to 1 headers comming soon, The head is slightly modified after MR, Croft book,
If i had good std cams MR ,Croft had the possibilety to grind camms for mee . But i have not.
My brand new german bilett camms givs good torque ,but dont suit my needs, They are Intake280 deg.10,9 lift, Lift at TDC 1,6mm Outlet 256 dedeg 9,6 in lift , Lift at TDC 1,3mm.
Dont know if these specks are with or wihtout clarance. But feels almost the same as OE cams, Gives a little more torque , After my meening to little duration.

The cams i choose must also bee lowcost , and i need somthing like medium race , Or at least so i can have a spinn on the roads too.Any good hints out there ? Regards Ove Thorkildsen Oslo Norway-
othorkild@c2i.net
GC_41

Guy Croft
Site Admin
Posts: 5024
Joined: Sun Jun 18, 2006 10:31 am
Location: Lincoln, UK
Contact:

Re: Need Camchafts for my 2,0 16v engine.used in my X1/9

Post by Guy Croft » Sun Mar 03, 2013 1:24 pm

engine has a 16v Tipo/Integrale type head in case anyone is wondering what cams are needed here..

GC
Guy Croft, owner

torkil
Posts: 72
Joined: Thu Dec 30, 2010 3:10 pm
Contact:

Re: Need Camchafts for my 2,0 16v engine.used in my X1/9

Post by torkil » Sun Mar 10, 2013 1:16 pm

påhenger kammer 007 (800x600) (2).jpg
German Camchafts In 280 /10,9MMLIFT Out 256 Lift9,6 . Lift at TDC in 1,3mm out 1,3mm
påhenger kammer 007 (800x600) (2).jpg (339.13 KiB) Viewed 1589 times
påhenger kammer 007 (800x600) (2).jpg
German Camchafts In 280 /10,9MMLIFT Out 256 Lift9,6 . Lift at TDC in 1,3mm out 1,3mm
påhenger kammer 007 (800x600) (2).jpg (339.13 KiB) Viewed 1589 times
GC_41

Guy Croft
Site Admin
Posts: 5024
Joined: Sun Jun 18, 2006 10:31 am
Location: Lincoln, UK
Contact:

Re: Need Camchafts for my 2,0 16v engine.used in my X1/9

Post by Guy Croft » Sun Mar 10, 2013 3:55 pm

they look like steel cams - you can't reprofile them


G
Guy Croft, owner

Guy Croft
Site Admin
Posts: 5024
Joined: Sun Jun 18, 2006 10:31 am
Location: Lincoln, UK
Contact:

Re: Need Camchafts for my 2,0 16v engine.used in my X1/9

Post by Guy Croft » Fri Mar 22, 2013 3:53 pm

Hi Ove

can you contact Daniel and pay his mailing on the cams please?

I will get them ground to L1/BD3 in April.

Sincerely,

G
Guy Croft, owner

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests